Cummins SPN 3556 FMI 5: Significado, Causas y Solución
Sensor NOx de Salida del Postratamiento — corriente por debajo de lo normal o circuito abierto, sensor no produce señal válida
Reviewed by ASE Certified Mechanics · Last updated July 25, 2026
Quick Answer
SPN 3556 FMI 5 = Sensor NOx de Salida del Postratamiento Circuito Abierto
Severity: 🟠 REVISAR PRONTO · System: NOx Sensor (Outlet) / Wiring Harness · ✅ Puede continuar con precaución
Referencia de Diagnóstico
| Campo | Detalles |
|---|---|
| Código | SPN 3556 FMI 5 |
| Protocolo | J1939 SPN: 3556 FMI: 5 |
| Componente | NOx Sensor (Outlet) / Wiring Harness |
| Fabricante | Cummins |
| Serie de Motor | ISX |
| Severidad | 🟠 REVISAR PRONTO |
| Referencia SAE | SAE J1939-73 Digital Annex — SPN 3556, FMI 5 |
Causas Posibles
- Circuito del calentador del sensor NOx abierto — el sensor no puede alcanzar temperatura de operación
- Cable de señal del sensor en circuito abierto por rozadura o desconexión del conector
- Falla de la celda de bomba interna del sensor NOx
- Conector del sensor corroído causando alta resistencia en circuito de calentador o señal
- Circuito de tierra del sensor abierto en conector del ECM
Causas Más Frecuentes (Ranking por Frecuencia)
- Corroded or loose sensor connector pins (35% of sensor/electrical faults)
- Wiring harness chafing causing intermittent open or short circuits (25%)
- Failed sensor providing out-of-range signal to ECM (20%)
- ECM 5V reference circuit overload from multiple sensor failures (10%)
- CAN bus communication fault from terminating resistor or module failure (10%)
Procedimiento de Diagnóstico Detallado
Siga estos pasos de diagnóstico para identificar la causa raíz de SPN 3556 FMI 5 en su Cummins ISX. Se recomienda una herramienta de escaneo de diagnóstico compatible con J1939.
- Connect scan tool and retrieve all active and inactive fault codes, noting which modules are reporting communication errors
- Check battery voltage and ground connections — low system voltage (below 11V) or poor grounds cause erratic sensor readings and communication faults
- Backprobe the suspect sensor connector and measure reference voltage (typically 5V), signal voltage, and ground with a digital multimeter — compare readings to OEM specifications
- Inspect wiring harness for chafing, especially at common failure points: engine pass-through connectors, valve cover gasket connectors, and frame rail routing near sharp edges
- Perform wiggle test on the harness while monitoring live data — intermittent connections will cause sensor readings to spike or drop when the harness is moved
- If CAN bus faults are present, check terminating resistors (should measure 60 ohms across CAN high and CAN low with the key off and batteries disconnected)
Reparación y Estimación de Costos
| Concepto | Rango de Costo |
|---|---|
| Piezas | $80 – $600 |
| Mano de Obra | 1–4 horas @ ~$150/hr = $150 – $600 |
| Total Estimado | $230 – $1,200 |
Sensor or connector replacement. Los precios varían según ubicación y concesionario.
Preguntas Frecuentes — NOx Sensor (Outlet) / Wiring Harness
How do I know if a sensor is bad or if the wiring is the problem?
Backprobe the sensor connector and measure reference voltage, signal, and ground. If the 5V reference is present and ground is good, but the signal is out of range, the sensor is likely bad. If reference voltage is missing or unstable, the problem is in the wiring or ECM. A wiggle test on the harness while monitoring live data will reveal intermittent connections.
Can I drive with a faulty sensor?
It depends on the sensor. Non-critical sensors (barometric pressure, fuel temperature) typically trigger CHECK SOON codes and the engine runs on a default value. Critical sensors (accelerator pedal, crankshaft position) can cause stalling or no-start conditions. If the engine runs normally despite the code, you can usually drive to a repair facility, but do not ignore the code indefinitely.
What causes CAN bus communication faults?
CAN bus faults are caused by wiring damage (chafed or cut wires), corroded connectors, failed terminating resistors, or a faulty module that corrupts bus communication. Heavy-duty trucks use J1939 CAN which requires 120-ohm terminating resistors at each end of the bus. Measuring 60 ohms across CAN high and CAN low (with power off) confirms the bus is intact.
How much does an ECM replacement cost?
A new ECM for a heavy-duty diesel engine costs $1,500–$4,000 for the part alone, plus 3–6 hours of labor for installation, programming, and parameter setup. Remanufactured ECMs are available for $800–$2,000. Always verify the ECM is truly faulty before replacing — many ECM codes are caused by wiring or sensor issues, not the ECM itself.
Why do sensor faults seem to happen more in wet weather?
Moisture ingress into sensor connectors causes corrosion and intermittent electrical contact. This is especially common at the engine harness pass-through connector (where wires enter the valve cover) and at under-hood sensor connectors that are not properly sealed. Dielectric grease on connector pins and OEM-rated weatherpack connectors help prevent moisture-related faults.
Procedimiento de Diagnóstico y Reparación
- Paso 1: Verificar continuidad del circuito del calentador del sensor NOx — debe medir 5-15 ohmios
- Paso 2: Inspeccionar conector del sensor por corrosión, pines sueltos o intrusión de humedad
- Paso 3: Verificar continuidad del circuito de tierra del sensor al ECM
- Paso 4: Comparar lecturas de NOx de salida con las de entrada — la salida debe leer significativamente más baja
- Paso 5: Reemplazar sensor NOx de salida si el circuito del calentador o señal está abierto
Preguntas Frecuentes
¿Es una falsa alarma o un problema real?
Los códigos REVISAR PRONTO rara vez son falsas alarmas. El ECM ha detectado un parámetro fuera del rango normal de operación. Las fallas de sensores a veces pueden causar lecturas falsas, pero la mayoría de los códigos REVISAR PRONTO indican un problema en desarrollo que empeorará si no se atiende. Use una herramienta de diagnóstico para verificar las lecturas de los sensores antes de reemplazar piezas costosas.
¿Puedo diagnosticar esto sin una herramienta de escaneo?
Se puede realizar una inspección visual básica sin herramienta de escaneo — revise los arneses de cableado por rozaduras, los conectores por corrosión y los componentes relacionados por daños físicos. Sin embargo, para verificar la falla, ver datos de sensores en vivo y confirmar la reparación, se recomienda encarecidamente una herramienta de diagnóstico de servicio pesado (o un adaptador OBD-II compatible con soporte J1939/J1708) para un diagnóstico preciso.
¿Qué tan pronto debo programar el servicio?
Programe el servicio dentro de los próximos 1–3 días hábiles. Aunque el vehículo puede continuar operando normalmente, retrasar la reparación aumenta el riesgo de que la falla suba a severidad REVISAR EN PRÓXIMA PARADA. Además, algunas condiciones REVISAR PRONTO son precursoras de fallas del sistema de emisiones que activarán una reducción de potencia obligatoria si no se atienden a tiempo.
Estimated Repair Cost
Typical repair: $100–800 (Parts: $50–500 + Labor: 1–3 hours) · Costs vary by make/model and location
Códigos Relacionados en Otros Sistemas
Códigos del mismo rango SPN, fabricante o sistema que también pueden ser relevantes:
SPN 3516 FMI 5
SPN 3556 FMI 0
SPN 1569 FMI 31
🔴 DETENER MOTOR
SPN 1322 FMI 31
SPN 4364 FMI 18
SPN 3031 FMI 9
🟠 REVISAR PRONTO
Síntomas Asociados
Referencias y Lecturas Adicionales
- SAE J1939-73: Capa de Aplicación — Diagnósticos. SAE International. Define la semántica de códigos de falla SPN 3556 / FMI 5 para redes CAN de servicio pesado. SAE J1939 Standard
- Cummins ISX Manual de Servicio: Procedimientos de diagnóstico OEM para fallas de NOx Sensor (Outlet) / Wiring Harness. Consulte la documentación oficial de servicio de Cummins para el número de serie específico de su motor.
- TMC RP 1210: Práctica Recomendada para Interfaz de Diagnóstico de Vehículos Basada en Windows. Technology & Maintenance Council (TMC) de American Trucking Associations.